|
|
KD80
Oct 19, 2018 14:06:33 GMT -5
via mobile
Post by sf on Oct 19, 2018 14:06:33 GMT -5
|
|
|
|
Post by Walms on Oct 19, 2018 16:05:47 GMT -5
Cool bike! I bet Kawi still has parts for those!
|
|
|
|
KD80
Oct 19, 2018 21:04:06 GMT -5
via mobile
Post by Curtis on Oct 19, 2018 21:04:06 GMT -5
Lots of parts still available 🤓
Send me a list
|
|
|
|
KD80
Oct 19, 2018 22:27:08 GMT -5
via mobile
Post by sf on Oct 19, 2018 22:27:08 GMT -5
Ok perfect....how about a factory service manual.
|
|
|
|
KD80
Oct 19, 2018 22:43:32 GMT -5
via mobile
Post by sf on Oct 19, 2018 22:43:32 GMT -5
|
|
|
|
KD80
Oct 20, 2018 4:12:31 GMT -5
via mobile
Post by Curtis on Oct 20, 2018 4:12:31 GMT -5
Will send you a pm later today
|
|
|
|
KD80
Oct 20, 2018 15:30:35 GMT -5
via mobile
Post by sf on Oct 20, 2018 15:30:35 GMT -5
Today after hockey it was so nice out I dug into the bike in the back yard. It has spark and gets fuel. Took the head off and it’s clean no carbon build up on the piston either. From what I can see there is no scoring on the cylinder walls. Took the carb off and lots of oil in the intake but the carb is nice and clean.
The air filter foam was completely broken down and hanging off so until I order a new one I cleaned it up and used one of the kids socks.
I can see through the intake everything is lubed up and shiny and I can shift through all gears.
When I get back from the next game I’m going to get some fresh gas and try to start it again.
|
|
|
|
KD80
Oct 20, 2018 18:01:33 GMT -5
via mobile
Post by Curtis on Oct 20, 2018 18:01:33 GMT -5
My PM keeps bouncing back. I can email you a copy of a FSM - shoot me a PM and I can get it off to you
|
|
|
|
Post by Walms on Oct 20, 2018 19:31:07 GMT -5
I’ll take one too Curtis! 👍
|
|
|
|
KD80
Oct 20, 2018 20:16:07 GMT -5
via mobile
Post by Curtis on Oct 20, 2018 20:16:07 GMT -5
I’ll take one too Curtis! 👍 You have a Kd80 ? |
|
|
|
KD80
Oct 20, 2018 20:53:12 GMT -5
via mobile
Post by sf on Oct 20, 2018 20:53:12 GMT -5
You building a pipe?😎
|
|
|
|
Post by Walms on Oct 21, 2018 4:45:44 GMT -5
I have worked on a pipe, I even have a couple kits laser cut, just for testing. I’m assuming the same engine as KE.
If so, the engine hasn’t changed since 1982, I have a few boxes of parts I’ve been collecting for my builds.
|
|
|
|
KD80
Oct 22, 2018 17:45:27 GMT -5
via mobile
Post by sf on Oct 22, 2018 17:45:27 GMT -5
So anybody repair a cracked float before? I’ll try soldering it closed tomorrow.
|
|
|
|
KD80
Oct 22, 2018 18:14:53 GMT -5
via mobile
Post by Curtis on Oct 22, 2018 18:14:53 GMT -5
Brass float ? Solder then all the time - lots of flux
|
|
|
|
KD80
Oct 22, 2018 21:45:47 GMT -5
via mobile
Post by sf on Oct 22, 2018 21:45:47 GMT -5
What’s the float height on this 4mm? I really need a manual I know. I can’t get fuel to flow when I hook it up to the carb no matter what I do.
|
|
